Burkert is the authorized BURKERT flow switches and BURKERT flow meters.

LEHIY Industrial is a distributor of Burkert flow meters and flow switches.

Commonly used Burkert flow meter models include: 8006, 8010, and 8025 Burkert insertion flow meters; 8030 and 8032 Burkert flow switches; 8035 Burkert vortex flow meters; 8045 Burkert electromagnetic flow meters; 8041 and 8071 Burkert authorized ultrasonic flow meters; and 8189 and 8098 Burkert surface acoustic wave flow meters, etc.

These Burkert flow meters are classic and commonly used.

Burkert flow meters - magnetic measurement impeller type Burkert flow switch

• : The 8010 INLINE Burkert flow switch is used to monitor pure, water-like liquids that must not contain magnetizable particles. The switch consists of a PowerD connector (S010) and a PowerD module (SE10) for electronic devices, which can be quickly and easily connected via a bayonet PowerD connector. The device indicates the presence of flow through a chip switch included in the electronic device module. The minimum/maximum switching point can be adjusted within a specific range for increasing and decreasing flow velocities via an adjusting bolt located on the electronic device module. Two types of PowerD SE10 electronic devices are available: - No flow open (NO): Flow closes the contact. - No flow close (NC): Flow opens the contact. The PowerD S010 connector has different interfaces and is available in two configurations: - With a small impeller (Area 1): Suitable for connectors DN15 to
• - With a large impeller (Area 2): Suitable for connectors DN32 to
• It integrates into piping systems at low cost, requiring no additional piping. The magnetic measurement principle allows for easy setting of the switching point via the adjusting bolt. Burkert Fluid Systems' best-selling and commonly used Burkert flowmeter series and introductions: 8006, 8010, 8025, 8030, 8032, 8035, 8045, 8041, 8071, 8189, etc. These are some classic and commonly used Burkert flowmeters. The small-flow oval gear Burkert flowmeter
• : This Burkert sensor is specifically designed for the measurement and batch control of high-viscosity liquids such as glue, honey, or oil. It can be easily matched with the 8025 and 8019 sensors and used for a variety of other applications. Based on the measurement principle of oval gears, this small-flow sensor has proven to be reliable and accurate in measuring flow. Good repeatability and a wide applicable flow and viscosity range are also design features of this flowmeter. Low pressure drop and high pressure resistance make this flowmeter suitable for various applications. All sensors are equipped with NPN open collector frequency output and frequency output with chip contacts, and have a built-in 1-meter long 5-wire cable. Suitable for high-viscosity media and compatible with various transmitters, it enables numerical display, control, signal transmission, on/off control, and batch control. Burkert Flow Meter - Fast-Reacting Burkert Gas Mass Flow Meter
• : A mass flow meter used to detect the mass flow rate of gases. This meter measures the mass flow rate of gases without being affected by interference factors (eg, pressure or temperature fluctuations). The Burkert sensor operates based on thermodynamic principles (constant-temperature anemometer). When the mass flow rate changes, the heat flux in the heating element needs to be altered to maintain a constant overtemperature. Measurement is performed in the main flow, directly providing the mass flow rate without correction. Because it measures in the main flow, the Burkert 8006 MFM features high power and low contamination sensitivity. It can be used as a gas flow meter for a variety of applications. Typical applications of the Burkert 8006 gas mass flow meter include gas flow measurement in the following fields: heat treatment technology, inspection agencies, packaging technology, food and beverage industry, environmental technology, etc. Burkert Flow Meters - Corrosive Gas Mass Flow Controller
• : The Mass Flow Controller (MFC) is particularly suitable for mass flow control of corrosive gases, which require a media-isolated sensor. A capillary thermal Burkert sensor enables rapid response. A direct-acting Burkert proportional valve as the actuator ensures excellent response sensitivity. An integrated PI controller gives the MFC superior control characteristics. The 8710 Burkert flow meter can be calibrated for two different gases, and users can switch between them. As an electrical interface, it provides both analog standard signals and fieldbus. Burkert also distributes Burkert flow meters and guides microwave sterile liquid level gauges
• : These are liquid level gauges with replaceable rod-shaped measuring probes for continuous liquid level measurement. They are designed for industrial applications and for measuring liquids in all process technology areas. However, since the new rod is made of 1.4435 stainless steel (Ra < 0.76 μm), its main applications include the food and beverage industry (NuG) and pharmaceutical containers. The Burkert 8189 flow meter can be used with PFA coating specifications when applied to corrosive liquids. Even severe process conditions, such as strong vapor formation, density fluctuations, or changes in dielectric constant, will not affect measurement accuracy. Condensate adsorbed or formed on the probe or container wall will not affect the measurement results. It is a general-purpose Burkert level gauge suitable for measuring liquids. Burkert Ultrasonic Flow Meter - Pressure Loss: This ultrasonic flow meter is used to measure the flow rate of water, even when the water has slight contamination. It consists of a Burkert electronics module and a Burkert brass connector with an integrated measuring tube. Flow can be easily established in the regulating section by combining it with a regulator and a regulating valve. Electrical connection is made via a 5-pole M12 five-pin device plug. Depending on the configuration, this Powerflow flowmeter is equipped with the following outputs: - a pulse output or - a pulse output and a 4-20 mA current output. Each configuration offers five different flow ranges: - QN 0.6 model DN15: 0.06 to 20 l/min (rated size 0.6 m³/h, ie, 10 l/min) - QN 1.5 model DN15: 0.1 to 50 l/min (rated size 1.5 m³/h, ie, 25 l/min) - QN 2.5 model DN20: 0.16 to 82 l/min (rated size 2.5 m³/h, ie, 41 l/min) - QN 3.5 model DN25: 0.6 to 116 l/min (rated size 3.5 m³/h, ie, 58 l/min) - QN 6.0 model DN25: 1 to 200 l/min (rated size 6.0 m³/h, ie, 100 l/min) Burkert 8098 Surface Acoustic Flow Meter (l/min) - Temperature Control Processes: Burkert surface acoustic wave (SAW) flow meters are ideal for temperature control applications, such as cooling or heating in metal or plastic processing, where smooth transport is crucial to ensure product quality. In short, the flow meter in the circuit must operate reliably. Simultaneously, a wide measurement range ensures accurate recording of operation and even minor leaks. With SAW flow meters, Burkert flow control systems offer practical solutions in this field. SAW flow meters consist of an electronic module, a measuring element, and brass or stainless steel fittings (for pipe connection). In cartridge applications, the measuring module can be easily removed from the fitting when needed. provide complete solutions for specialized applications and offer relevant Burkert flow meter verification and certification. This means that Burkert flow meters are reliable, flexible, and have a wide measurement range, suitable for all temperature control process applications.

Share Article